How to Set up a Tub Yourself
How to Set up a Tub Yourself
Blog Article
Presented here in the next paragraph you can get a lot of reliable additional info on the subject of How to Install a Bathtub Yourself.
Installing a tub isn't exactly rocket science, yet it does need strong plumbing, woodworking, and sometimes, tiling abilities. Replacing an old bath tub with a brand-new one is also a reasonably tough project. If the old bathtub is readily accessible, the project can relocate rapidly; if you need to open a wall to get rid of the old tub as well as position the brand-new bathtub, the job is much harder. In either case, the task is within a residence handyman's abilities, although you will require a helper to vacate the old tub and also embeded in the new one. Ensure you have actually qualified on your own for the task and also fit attempting it. Instead of employing a contractor to take control of a halfway-completed job, it is far better to consider using one before you start. Chances are you might need an expert plumber to make tube links.
This article will certainly help you set up a brand-new bathtub in your shower room if you have actually already acquired a brand-new tub as well as don't need to transform the plan of your previous water pipes.
Your devices as well as product checklist should consist of the following:
Getting ready for the Installment
Firstly, the sustaining frame provided with the bath ought to be fitted (if called for) according to the producer's directions. Next, fit the taps or mixer to the bath tub. When fitting the faucet block, it is important to make certain that if the faucet comes with a plastic washer, it is fitted in between the bathroom and the faucets. On a plastic bathroom, it is also practical to fit a sustaining plate under the taps system to stop strain on the tub.
Fit the adaptable tap ports to the bottom of both taps utilizing 2 nuts and also olives (sometimes supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the outlet through the hole in the bathroom. Make use of the nut supplied by the producer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the adaptable overflow pipeline to the overflow outlet. After that, screw the pipe to the overflow face which must be fitted inside the bathroom. Make sure you use all of the supplied washing machines.
Attach the catch to the bottom of the waste outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Connect the bottom of the overflow tube in a similar manner.The bath must currently prepare to be suited its final position.
Removing Old Taps
If you need to change old faucets with brand-new ones as a part of your installment, after that the first thing you should do is disconnect the supply of water. After doing so, switch on the taps to drain pipes any type of water continuing to be in the system. The procedure of getting rid of the existing faucets can be fairly bothersome due to the restricted access that is frequently the situation.
Utilize a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that connects the supply pipes to the taps. Have a cloth ready for the remaining water that will come from the pipes. Once the supply pipes have actually been gotten rid of, utilize the exact same tool to loosen the nut that holds the taps onto the bath/basin. You will need to quit the solitary faucets from transforming throughout this process. Once the taps have been removed, the holes in the bath/basin will certainly need to be cleansed of any type of old sealing compound.
Before moving on to fit the brand-new faucets, compare the pipe connections on the old faucets to the brand-new faucets. If the old taps are longer than the new taps, after that a shank adapter is needed for the new taps to fit.
Installing the Bath tub
Making use of both wooden boards under its feet, put the bathtub in the called for placement. The wood boards are valuable in evenly spreading the weight of the bath tub over the area of the boards as opposed to concentrating all the weight onto 4 small points.
The next objective is to make certain that the tub is leveled all round. This can be achieved by checking the level as well as adjusting the feet on the bath tub till the spirit level reads degree.
To set up taps, fit all-time low of the furthest adaptable tap adapter to the suitable supply pipeline by making a compression sign up with; then do the exact same for the other faucet.
Switch on the water and inspect all joints and also new pipework for leakages as well as tighten them if necessary. Load the tub as well as likewise check the overflow electrical outlet as well as the normal electrical outlet for leaks.
Ultimately, repair the bathroom paneling as explained in the manufacturer's user's manual. Tiling as well as securing around the tub needs to wait up until the bathtub has actually been used at the very least once as this will certainly settle it right into its final placement.
Fitting New Touches
If the tails of the new faucets are plastic, then you will certainly need a plastic port to prevent damage to the string. One end of the connector fits on the plastic tail of the faucet and the various other end supplies a connection to the existent supply pipelines.
If you require to fit a monobloc, then you will certainly call for lowering couplers, which connects the 10mm pipeline of the monobloc to the standard 15mm supply pipe.
Next, position the faucet in the mounting opening in the bath/basin ensuring that the washing machines remain in location in between the tap as well as the sink. Safeguard the tap in position with the manufacturer supplied backnut. As soon as the tap is securely in place, the supply pipelines can be connected to the tails of the faucets. The faucets can either be attached by using corrugated copper piping or with normal tap adapters. The previous type should be linked to the faucet finishes initially, tightening only by hand. The supply pipelines can later be linked to the various other end. Tighten up both ends with a spanner after both ends have been linked.
Tiling Around the Bath tub
In the area where the bath satisfies the floor tile, it is necessary to seal the accompanies a silicone rubber caulking. This is essential as the installation can relocate enough to crack a rigid seal, triggering the water to permeate the wall surface in between the bathroom and also the tiling, bring about complications with dampness and feasible leakages to the ceiling listed below.
You can choose from a variety of coloured sealants to assimilate your components and also fittings. They are sold in tubes and cartridges, as well as can securing voids approximately a width of 3mm (1/8 inch). If you have a larger gap to fill up, you can fill it with spins of drenched paper or soft rope. Bear in mind to constantly load the bathtub with water before sealing, to allow for the movement experienced when the bathtub remains in usage. The sealer can split rather very early if you do not take into consideration this activity prior to sealing.
Additionally, ceramic coving or quadrant tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are likewise quickly offered on the marketplace. It is a good idea to fit the ceramic tiles utilizing waterproof or water resistant sticky as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Hopefully you liked our section about How to Install a Bathtub. Thank you for taking the time to read through our blog post. Enjoyed reading our content? Please share it. Help other people locate it. I enjoy reading our article about Installing A Bathtub.
Information Here
Report this page